Photopolymerizable hybrid sol-gel are extremely interesting for optical and photonic applications. They combine the properties of glasses with the possibility of photopatterning the layer at the micrometer scale. The presented results concern the generation of volume gratings created by transmission and reflection using an interferences pattern at 514 nm. In transmission, the diffraction efficiencies were going from 30 % to 95 % (ratio of the diffracted intensity to the diffracted plus transmitted intensities) for a thickness ranging respectively from 40 μm to 100 μm and a spatial
frequency of 1000 lines/mm. It corresponded to a refractive index modulation estimated between 4 and 5 x 10-3according to Kogelnik's theory. Reflection gratings with fringe spacing of 0.17 or 0.39 μm were recorded in the material. In normal incidence light beams were highly diffused, whatever the wavelength in the visible range. On the contrary, in oblique incidence, light beams were transmitted through the device without being diffused. This unusual
behavior is not yet explained. Applications for information storage can be expected in view of the experimental results, the ease of use and the versatility of this hybrid material.
Noticeable refractive index modulations (difference between the refractive index of high-density areas and the index of low-density areas ~8x10-3) can be created by photostructuration of acrylic films. The light pattern created by the interference of two plane waves induces inhomogeneous polymerization and mass diffusion processes, due to concentration gradients of monomer and dye, giving rise "in situ" to a structuration of the material at the microscopic scale. As the species involved in the initiation mechanism are gradually consumed as the hologram builds up, the incident dose is determined in order to reach full completion of the reaction at the end of the recording, i.e. to obtain stable gratings. This property makes photopolymers attractive materials for number of applications, especially in holography. A great advantage of these materials over other recording systems is that no chemical or heating post-treatment is required after illumination to reveal the hologram. Diffraction efficiencies of ca 80 % were obtained at 514 nm for transmission holograms with a fringe spacings between 0.2 and 5 μm. 675 mJ/cm2 corresponding to a bleaching of the dye of 85% allows non-destructive reading at an active wavelength (green light). Miscellaneous photonic parameters (chemical composition, intensity, dose...) were tested by grating recording. Taking into account all these data, improvement of the material is possible in view of data storage applications.
Free-radical photocurable hybrid material was used for the creation of crack free holographic gratings, showing only a refractive index modulation. Organic-inorganic materials based on the sol-gel synthesis of alkoxysilanes have demonstrated their great potential for coating and optical applications. In a first step, hydrolysis and condensation reactions were led under mild conditions along the same way as in classical sol-gel glasses. Partial elaboration of the silicate backbone was thus achieved. Then, with the use of a photoinitiator, free-radical polymerization was proceeded by irradiating the material under UV or visible light. A spatially controlled photopatterning can be thus achieved to create optical elements having the hardness of a glass-like material. The presented results concern the formation of gratings created by transmission using interference pattern at 514 nm. Diffraction efficiencies up to 90 % were reached for 1000 lines/mm in transmission, corresponding to a refractive index modulation amplitude of 4.10-3 (according to the Kogelnik's theory). To elaborate non linear quadratic optical devices, hybrid sol-gel matrixes were doped with push-pull chromophores. Such a photosensitive system enables simultaneous photopatterning of the layer and poling of the NLO molecules. Experiments were realized during the photopolymerization step, in order to study the freezing of the non-centrosymetric orientation of the dispersed NLO chromophores.
Hybrid organic-inorganic materials based on the sol-gel synthesis of organically modified silicon alkoxides have demonstrated their great potential for optical applications. They offer a high versatility in terms of chemical, physical properties and macroscopic shape molding of the final component. In a first step, hydrolysis and condensation reactions are led along the same way as in classical sol-gel glasses. Partial elaboration of the silicate backbone is thus achieved. Then, free-radical polymerization is proceeded by irradiating the sample under UV or visible light. Finally, the material consists of two crosslinked inorganic and organic networks that are interpenetrated. The present paper focuses on a photolithographic process allowing the generation of relief optical elements without requiring a wet treatment to reveal the latent image. It enables a low cost, simple and quick method for the fabrication of integrated micro-optical components with a spatial frequency up to 250 l/mm. The aim of the present work is to give particular attention to the kinetic aspects of the polymerization of the organic component. The control of the C=C double bonds conversion of acrylate functionalized alkoxides in case of photopolymerization is therefore, an essential issue to tailor material properties. The study also focuses on the influence of physico-chemical parameters that govern the relief generation. Kinetics of surface corrugation point out the importance of strain relaxation, mass-transfer by flowing and organic network formation during the photolithographic process. Some illustrations of the generated diffraction gratings are given.
The present paper deals with the development of hybrid sol-gel glasses as host matrixes for molecules having quadratic NLO properties. Second order non-linearities can be observed after poling in order to orient these molecules. However, due to their small size, thermal relaxation processes lead to a decrease of the induced orientation with time. Host matrixes showing a high rigidity and corresponding to a final material presenting a reduced free volume should overcome this drawback. An interesting way is to use the rigidity conferred by an organic-inorganic sol-gel matrix that can polymerize under irradiation. Photopatterning of the layer and simultaneous copolymerization of the hybrid precursor with functionalized chromophores should enhance the second order NLO response. The results presented in this paper focus on the formulation and conditioning of laminated hybrid sol-gel layers with a thickness of 100 μm that remain crack-free under condensation and photopolymerization. Results are presented concerning the generation of 1 μm gratings obtained under spatially controlled visible illumination using interference pattern at 514 nm. Diffraction efficiencies up to 90 % are obtained for an incident intensity of 30 mW.cm-2. The next step is now the incorporation of functionalized chromophores in the hybrid sol-gel matrix leading to a study of NLO properties of the final material.
Sol-gel process is for more than one decade an interesting way to synthesize inorganic-organic composites under a soft chemistry route. Recently a process for the fabrication of self-developing diffractive optical elements has been developed. The inorganic part of the molecule was an alkoxysilane that reacted via hydrolysis and condensation reactions at room temperature, thus leading to a gel. The mild conditions under which the inorganic part of the material was prepared are compatible with the presence of an organic moiety, a methacrylate function. The organic network was produced via spatially controlled UV illumination using amplitude masks. Surface relief gratings were obtained via this photochemical step ; generation of relief resulted from mass-transfer by diffusion and gradient of surface free energy. No etching process was required. Although the hybrid sol-gel material was assumed to perform along the same lines as the one involving all-organic photopolymers, the influence of the inorganic moieties on the photopolymerization of the methacrylate function remained unknown. Characteristics of the photopolymerization process taking place in hybrid sol-gel materials were investigated by UV and FTIR spectroscopies. Besides the study of the organic network, NMR investigations led information relative to the inorganic network formation during the sol ageing. The whole results provide insights into the influence of the temperature during the photochemical step. Relief gratings generated under various conditions and for a large scale of spatial frequencies are presented. Sinusoidal to almost binary profiles were obtained in a one-step process.
Growing interest in miniaturized optical components for various applications such as optical interconnection systems and telecommunication industry have led to the development of several techniques that are used in the fabrication of micro-optical elements. One approach involves the use of polymers as recording materials: these are flexible, highly transparent and cheap. The technique described in the present paper is founded on the ability of self-processing photopolymers to generate refractive microlens arrays. Spatially controlled illumination of a photosensitive layer induces an inhomogeneous photopolymerization involving a mass-transport process of reactive species and generating a relief in the photopolymer layer. The presentation focuses on the fabrication of microlens arrays through photopolymerization with the green line of an argon-ion laser. Surface tension and differential volume shrinkage turned the illuminated area into good quality lenses. The fabricated lens arrays exhibit diameters ranging from less than 20 micrometers to more than 500 micrometers and focal lengths from 100 micrometers to a few millimeters, depending on photonic, optical and physico-chemical parameters. This imaging technique is highly flexible as regards height, shape and optical properties of the lenses that are produced. By starting from the same background, one can also fabricate diffractive optical elements such as gratings and duplicate computer-generated holograms that come increasingly into prominence as the micro-opto-electro-mechanical field expands.
Local changes in thickness occurring upon controlled exposure to light of photopolymers capable of storing optical information were investigated. The image that developed as a relief in the photosensitive layer exhibited a complete self-processing character because it did not require any chemical post-treatment. Special attention was given to the effect of the gradient of chemical composition, the volume shrinkage, the gradient of surface free energy leading to mass transfer during the generation of low frequency relief gratings. This imaging techniques provides a high flexibility as regards height and shape of the generated relief. It allows fabrication of both diffractive and refractive optical elements that come increasingly into prominence as the micro-opto-electro-mechanical field expands.
The use of photopolymer films to record information by optical methods is described. The final result in such thin polymer films is its surface modulation that develops under the sole action of light and does not require any chemical treatment. The relief generating process permits the fabrication of diffractive and refractive optical elements that work in transmission or in reflexion. This last mode is achieved when a metal thin film is overcoated on its surface. Low spatial frequency gratings, microlenses and micromirrors were made. Several diffractive elements using computer generated holograms were also fabricated.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.