The 3-dimensional (3D) imaging is an important area which can be applied to face detection, gesture recognition, and 3D reconstruction. Many techniques have been reported for 3D imaging using various methods such as time of fight (TOF), stereo vision, and structured light. These methods have limitations such as use of light source, multi-camera, or complex camera system. In this paper, we propose the offset pixel aperture (OPA) technique which is implemented on a single chip so that the depth can be obtained without increasing hardware cost and adding extra light sources. 3 types of pixels including red (R), blue (B), and white (W) pixels were used for OPA technique. The aperture is located on the W pixel, which does not have a color filter. Depth performance can be increased with a higher sensitivity because we use white (W) pixels for OPA with red (R) and blue (B) pixels for imaging. The RB pixels produce a defocused image with blur, while W pixels produce a focused image. The focused image is used as a reference image to extract the depth information for 3D imaging. This image can be compared with the defocused image from RB pixels. Therefore, depth information can be extracted by comparing defocused image with focused image using the depth from defocus (DFD) method. Previously, we proposed the pixel aperture (PA) technique based on the depth from defocus (DFD). The OPA technique is expected to enable a higher depth resolution and range compared to the PA technique. The pixels with a right OPA and a left OPA are used to generate stereo image with a single chip. The pixel structure was designed and simulated. Optical performances of various offset pixel aperture structures were evaluated using optical simulation with finite-difference time-domain (FDTD) method.
A 3dimensional (3D) imaging is an important area which can be applied to face detection, gesture recognition, and 3D reconstruction. In this paper, extraction of depth information for 3D imaging using pixel aperture technique is presented. An active pixel sensor (APS) with in-pixel aperture has been developed for this purpose. In the conventional camera systems using a complementary metal-oxide-semiconductor (CMOS) image sensor, an aperture is located behind the camera lens. However, in our proposed camera system, the aperture implemented by metal layer of CMOS process is located on the White (W) pixel which means a pixel without any color filter on top of the pixel. 4 types of pixels including Red (R), Green (G), Blue (B), and White (W) pixels were used for pixel aperture technique. The RGB pixels produce a defocused image with blur, while W pixels produce a focused image. The focused image is used as a reference image to extract the depth information for 3D imaging. This image can be compared with the defocused image from RGB pixels. Therefore, depth information can be extracted by comparing defocused image with focused image using the depth from defocus (DFD) method. Size of the pixel for 4-tr APS is 2.8 μm × 2.8 μm and the pixel structure was designed and simulated based on 0.11 μm CMOS image sensor (CIS) process. Optical performances of the pixel aperture technique were evaluated using optical simulation with finite-difference time-domain (FDTD) method and electrical performances were evaluated using TCAD.
Recently, CMOS image sensors (CISs) have become more and more complex because they require high-performances such as wide dynamic range, low-noise, high-speed operation, high-resolution and so on. First of all, wide dynamic range (WDR) is the first requirement for high-performance CIS. Several techniques have been proposed to improve the dynamic range. Although logarithmic pixel can achieve wide dynamic range, it leads to a poor signal-to-noise ratio due to small output swings. Furthermore, the fixed pattern noise of logarithmic pixel is significantly greater compared with other CISs. In this paper, we propose an optimized linear-logarithmic pixel. Compared to a conventional 3-transistor active pixel sensor structure, the proposed linear-logarithmic pixel is using a photogate and a cascode MOSFET in addition. The photogate which is surrounding a photodiode carries out change of sensitivity in the linear response and thus increases the dynamic range. The logarithmic response is caused by a cascode MOSFET. Although the dynamic range of the pixel has been improved, output curves of each pixel were not uniform. In general, as the number of devices increases in the pixel, pixel response variation is more pronounced. Hence, we optimized the linear-logarithmic pixel structure to minimize the pixel response variation. We applied a hard reset method and an optimized cascode MOSFET to the proposed pixel for reducing pixel response variation. Unlike the conventional reset operation, a hard reset using a p-type MOSFET fixes the voltage of each pixel to the same voltage. This reduces non-uniformity of the response in the linear response. The optimized cascode MOSFET achieves less variation in the logarithmic response. We have verified that the optimized pixel shows more uniform response than the conventional pixel, by both simulation and experiment.
In this paper, a binary complementary metal oxide semiconductor (CMOS) image sensor with a gate/body-tied (GBT) metal oxide semiconductor field effect transistor (MOSFET)-type photodetector is presented. The sensitivity of the GBT MOSFET-type photodetector, which was fabricated using the standard CMOS 0.35-μm process, is higher than the sensitivity of the p-n junction photodiode, because the output signal of the photodetector is amplified by the MOSFET. A binary image sensor becomes more efficient when using this photodetector. Lower power consumptions and higher speeds of operation are possible, compared to the conventional image sensors using multi-bit analog to digital converters (ADCs). The frame rate of the proposed image sensor is over 2000 frames per second, which is higher than those of the conventional CMOS image sensors. The output signal of an active pixel sensor is applied to a comparator and compared with a reference level. The 1-bit output data of the binary process is determined by this level. To obtain a video signal, the 1-bit output data is stored in the memory and is read out by horizontal scanning. The proposed chip is composed of a GBT pixel array (144 × 100), binary-process circuit, vertical scanner, horizontal scanner, and readout circuit. The operation mode can be selected from between binary mode and multi-bit mode.
A novel high-sensitivity active pixel sensor (APS) with a variable threshold photodetector has been presented and for the first time, a simple SPICE model for the variable threshold photodetector is presented. Its SPICE model is in good agreement with measurements and is more simpler than the conventional model. The proposed APS has a gate/body-tied PMOSFET-type photodetector with an overlapping control gate that makes it possible to control the sensitivity of the proposed APS. It is a hybrid device composed of a metal-oxide-semiconductor field-effect transistor (MOSFET), a lateral bipolar junction transistor (BJT) and a vertical BJT. Using sufficient overlapping control gate bias to operate the MOSFET in inversion mode, the variable threshold photodetector allows for increasing the photocurrent gain by 105 at low light intensities when the control gate bias is -3 V. Thus, the proposed APS with a variable threshold photodetector has better low-light-level sensitivity than the conventional APS operating mode, and it has a variable sensitivity which is determined by the control gate bias. The proposed sensor has been fabricated by using 0.35 μm 2-poly 4-metal standard complementary MOS (CMOS) process and its characteristics have been evaluated.
In this paper, a complementary metal oxide semiconductor (CMOS) binary image sensor based on a gate/body-tied
(GBT) MOSFET-type photodetector is proposed. The proposed CMOS binary image sensor was simulated and measured
using a standard CMOS 0.18-μm process. The GBT MOSFET-type photodetector is composed of a floating gate (n+-
polysilicon) tied to the body (n-well) of the p-type MOSFET. The size of the active pixel sensor (APS) using GBT
photodetector is smaller than that of APS using the photodiode. This means that the resolution of the image can be
increased. The high-gain GBT photodetector has a higher photosensitivity compared to the p-n junction photodiode that
is used in a conventional APS. Because GBT has a high sensitivity, fast operation of the binary processing is possible. A
CMOS image sensor with the binary processing can be designed with simple circuits composed of a comparator and a Dflip-
flop while a complex analog to digital converter (ADC) is not required. In addition, the binary image sensor has low
power consumption and high speed operation with the ability to switch back and forth between a binary mode and an
analog mode.
This paper presents a novel high-sensitivity and wide dynamic range complementary metal oxide semiconductor
(CMOS) active pixel sensor (APS) with an overlapping control gate. The proposed APS has a high-sensitivity gate/bodytied
(GBT) photodetector with an overlapping control gate that makes it possible to control the sensitivity of the
proposed APS. The floating gate of the GBT photodetector is connected to the n-well and the overlapping control gate is
placed on top of the floating gate for varying the sensitivity of the proposed APS. Dynamic range of the proposed APS is
significantly increased due to the output voltage feedback structure. Maximum sensitivity of the proposed APS is 50
V/lux•s in the low illumination range and dynamic range is greater than 110 dB. The proposed sensor has been fabricated
by using 2-poly 4-metal 0.35 μm standard CMOS process and its characteristics have been evaluated.
Various approaches have been utilized to extend the dynamic range of the CMOS image sensor, which are based on a
linear-logarithmic CIS, overflow integration capacitor and multiple sampling or individual pixel resetting. These
approaches, however, suffer from noise, nonlinearity, lower sensitivity, reduced operating speed and lower resolution. In
order to overcome these problems, we have previously proposed a dynamic range extension method by combining output
signals from two photodiodes with different sensitivities, such as a high-sensitivity photodiode and a low-sensitivity
photodiode. The proposed active pixel sensor has been fabricated by using 2-poly 4-metal standard CMOS process and
its characteristics have been measured. It is found that charges in the high- and low-sensitivity photodiodes could be
mixed each other and the lost image information of the high-sensitivity photodiode could be regenerated using the
charges in the low-sensitivity photodiode, as shown by simulation results. Dynamic range extension of the proposed
active pixel sensor has been experimentally verified.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.